INDUSTRIAL PLANT EQUIPMENT
Used Metalworking Machinery
Phone 847 998-8882 Fax 847 998-8883
PO BOX 2278 * Northbrook, IL 60065-2278
| Working surface width: | 120" |
| Vert distance table to Spdl centerline: | 0 - 144" |
| Length of table feed & traverse: | 24 feet |
| Range of quill travel from face of head: | 0 - 24" |
| Spindle speed range: | 10 - 130rpm |
| Fixture thickness holding capacity: | 14" - 40" |
| Fixture width holding capacity: | 36" - 90" |
| Fixture length holding capacity: | 58" - 21-1/2 feet |
| O/A Machine length: | 52.5 feet |
| Net weight with both Fixtures: | 610,000 lbs (277 metric tons |
| This machine consists of a
bed and table and a main housing carrying a single spindle 100hp motor-driven head having
vertical feed and traverse movement. The spindle is equipped with a No. 450 taper, 4-1/2" in diameter at the large end, ¾" diameter taper per foot. The Machine Bed has a weight bearing capacity of 740,000 lbs. The Spindle, which is driven by a 100hp motor drive, is supported by a 22" diameter Quill. This machine was designed to machine extra large Dies used in an extremely large Closed Die Forging Press. It is still installed under power and is available for immediate inspection and delivery. |
| Capacity: Vertical distance from table to centerline of spindle 0-144" Length of table feed and traverse 24' Length of quill travel from face of head 0-24" Bed (3 ways): Width across travel ways 112" Overall length, approx. 52.5 |
Table: |
| Housing: Width across housing ways 90" |
| Head: Movement on housing is made through two (2) elevating screws. Hand-operated locks Contains a quill which carries the spindle Spindle is driven by a 100 HP adjustable speed drive DC motor through gearing Flywheel on spindle drive |
Spindle: |
| Quill: Spindle quill diameter 22" Power and hand adjustment 24" Power adjustment is independent of table and head movement and provides feed and traverse as shown under "Feed & Traverse Rates" below Hand operated lock |
| Spindle
Speeds: Spindle speed, approx. 10-130 RPM The spindle has three (3) ranges of speed. The medium range starts at 14 RPM, and the high-speed range is full capacity of the 100 hp drive motor. The low speed range is at a limited capacity of 75 hp |
| Feed
Distribution: The machine is arranged with two (2) 2-Motor feed boxes, one for the head feed located on the top of the housing and one for the table located on the left hand side of the bed |
| Feed & Traverse Rates: |
Feed |
Rapid Traverse |
|
Table |
3/4" – 36" per minute |
20 ft. per min |
Head |
1/4" – 12" per minute |
8 ft. per min |
| Quill is equipped with an electronic feed motor providing feed and traverse movements ranging from ¾" – 24" a minute |
| Lubrication: Pumps included for lubrication gearing in saddle, top plate, Johnson Drive, bed ways and feed boxes. Hand pumps for lubricating elevating screw nuts, saddle clamp gibs and ways. Zerk fittings used for remaining points. |
| Motors and Electrical Equipment: |
Qty. |
Description |
1 |
Main Motor 100 hp, 575/1725 RPM, 230 volts, DC, drive motor |
2 |
Feed Motor 7-1/2 hp, 575/2300 RPM, DC |
2 |
Head & Table Drive Motors 40 hp, AC, foot mounted traverse motors |
2 |
Lubricating Pump Motors ½ hp, AC, |
1 |
Quill Adjust Motor 3 hp, 1150/2300 RPM, DC, 65/2300 FPM |
1 |
Coolant Pump Motor 2 hp |
1 |
Table Clamp Motor 15 ft. lb., 1800 RPM, Shell type |
| Electrics: 230 volts, DC 440 volts, AC The DC motors obtain their DC power from a 900 kw motor generator set which is driven by a 150 hp motor |
Machine
controls:
|
| Coolant: A motor driven coolant pump and piping supplies coolant to the cutter from a sump in the foundation. The foundation is constructed to drain coolant from around the machine into the sump. |
| Chip Conveyor: The machine has a "shaker" type chip conveyor located in the foundation on the right hand side of the machine. This chip conveyor is arranged to discharge the chips into a sump at the front of the machine in the foundation. |
| Weight: Net weight 330,000 lbs |
| CLAMPING FIXTURES AVAILABLE AT NO ADDITIONAL COST |
(2) Hydraulic Clamping
Fixtures: Capacity – the fixture is adjustable for holding the following sizes
of die blocks: Electrics – 440 volt, 3 phase, 60 cycle, AC as follows: (1) 7-1/2" HP AC motor for adjusting crossrail Weight – estimated weight of each fixture and
its parts is 140,000 lbs Travel: Hydraulic Unit: Vickers |
| NOTE: Every effort has been made to assure the above specifications are accurate, however, it is the sole responsibility of the buyer to confirm the actual model, capacity, attachments, accessories, extras and condition. We urge buyers to inspect all machinery and equipment prior to purchase. |
Subject to Prior Sale
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |
 |